Home > 3com Etherlink > 3com Etherlink Iii Isa Linux Driver

3com Etherlink Iii Isa Linux Driver

Cards in PnP mode may conflict with other resources in the system. The driver could not allocate the interrupt it wanted. Two years ago I built a retro Win98se computer and tried to install ISA 3COM NIC. ep0: strange connector type in EEPROM: assuming AUI The driver does not know what to do with the information the EEPROM has about connectors, so it is assuming the worst. have a peek here

The flag "0x3c509" must be set to avoid conflicts with other card types when overriding the I/O address. Privacy Policy server: web2, load: 1.08 Linux and the 3Com EtherLink III Ethercards This page contains information on using Linux with 3Com EtherLink III series ethercards. The timer tick interrupt should always be incrementing faster than the others. Ubuntu manuals go Provided by: freebsd-manpages_9.2+1-1_all NAME ep — Ethernet driver for 3Com Etherlink III (3c5x9) interfaces SYNOPSIS To compile this driver into the kernel, place the following line in your http://manpages.ubuntu.com/manpages/trusty/man4/ep.4freebsd.html

No received packets If a 3c509, 3c562 or 3c589 can successfully transmit packets, but never receives packets (as reported by /proc/net/dev or 'ifconfig') you likely have an interrupt line problem. Only the IRQ and transceiver setting may be overridden when using the river as a module. They work just fine and see no need to settle for CDRW drives.Hope this helps,Bob Flag Permalink This was helpful (0) Collapse - Progress ??

Als when trying it that way I get a docbook error notice.So it seems very strange to me that sucht good distro as Centos does no network ISA support, why not? The ep driver supports the 595 and 895 cards. There is so many to choose from. Powered by the Ubuntu Manpage Repository generator maintained by Dustin Kirkland © 2010 Canonical Ltd. With a status of 0x2011 you are receiving packets faster than they can be removed from the card.

lrs_state ^ 0xcf : lrs_state; 235 } 236 /* For the first probe, clear all board's tag registers. */ 237 if (current_tag == 0) 238 outb(0xd0, id_port); 239 else /* Otherwise This leads me to ask ?How is one to tell the ISA NIC is not working?? As part of printing the message, it check the interrupt status again. http://drivers.softpedia.com/get/NETWORK-CARD/3COM/3Com-EtherLink-III-16Bit-ISA-Network-Interface-Card-3C509-and-3C509B.shtml I believe you are the person who warned me about these kinds of drives.

The 1.2.13 driver fails to note this failure and doesn't reset the card. Preview post Submit post Cancel post You are reporting the following post: 3Com EtherLink III ISA (3C509/3C509b) in ISA mode This post has been flagged and will be reviewed by our Beware! To override this, use the following media options with ifconfig(8) or in your /etc/rc.conf file. 10base5/AUI Use the AUI port. 10base2/BNC Use the BNC port. 10baseT/UTP Use the UTP port.

Setting two cards to 10base2/IRQ10 and AUI/IRQ11 is done by using the xcvr and irq module options: options 3c509 xcvr=3,3 irq=10,11 Available Transceiver Types The available transceiver types are 0 default The messages only occur when you get packets with errors or are temporarily running out of memory. Blog Unsubscribe About Us Overview Contact Us Take our Site Survey Testimonials Copyright © 1996 - DriverGuide is an iCentric Corporation Company. You didn't write one word if you were looking into setting the IRQ for your card or if you remembered the bad old days.Bob Flag Permalink This was helpful (0) Collapse

SOFTPEDIA Windows Drivers Games Mac Android Linux News Softpedia > Drivers > Network Card > 3COM >3Com EtherLink III 16-Bit ISA Network Interface Card navigate here ep0: eeprom failed to come ready The eeprom failed to come ready. All other distro's do as far as I know, also Fedora and Suse.Can anybody help me please with this? ep0: <%s> at x0%03x in PnP mode This card appears to be in Plug and Play mode.

I ended up using a PCI version of the same card and still had to setup 2 hardware profiles so the IRQs would not conflict with the ISA modem, USB wireless Allows the boot-time parameter to override the EEPROM specified IRQ line. (I'm still reluctent to allow setting the I/O address with this method.) Always maps the card to the EEPROM location, Thanks. Check This Out Possible problems are a "green" mode enabled that slows the processor down when there is no keyboard activitiy.

All rights reserved. If you believe this post is offensive or violates the CNET Forums' Usage policies, you can report it below (this will not automatically remove the post). Here is why I ask.

When a packet is to be transmitted, the driver checks if an interrupt is pending.

some other device or device driver hogging the bus or disabling interrupts. The driver in kernel 2.0 (and the updated driver for 1.2.13 should avoid this problem. for it to complete. 646 Assume extra-fast 16Mhz bus. */ 647 outb(EEPROM_READ + index, id_port); 648 649 /* Pause for at least 162 us. Close Update Your Review Since you've already submitted a review for this product, this submission will be added as an update to your original review.

Avoids the spurious "interrupt for unknown device" message. Ensure your BIOS is configured correctly to exclude resources used by the 3c509, especially IRQs, to avoid unpredictable behavior. This may happen in extremely low memory conditions. this contact form I had to change the IRQ/address around to fix the conflicts during the install and all seemed well.

RxMulticast : 0) 825 | (dev->flags & IFF_PROMISC ? We change to register window 6, so this should be run 883 single-threaded if the device is active. The 1.2.13 driver always uses 0x100 as the "ID Port", preventing an ISA 3c509 from being detected with some hardware configurations. Because of your heads up I was finally able to setup the CDROM drive to work in DOS.

Top mkoco Posts: 6 Joined: 2005/06/17 11:27:06 Contact: Contact mkoco Website install 3Com 3C509B (Etherlink III ISA) in text mode?? Sorry but the details and any "do this" is not in these posts yet.As to that old CDROM drive, the interface was called MKE Panasonic (but since this is so long Thank You for Submitting an Update to Your Review, ! Flag Permalink This was helpful (0) Collapse - REAL PROGRESS !!!

The 1.2.13 driver may occasionally produce the following message: eth0: Missed interrupt, status then 2011 now 2000 Tx 00 Rx 8000. The updated driver searches for an empty location of the form 0x1[0-F]0 to use as the ID Port, however this reportedly does not fix the problem with some "32 bit" sound My guess is "NO". All rights reserved.

Uploaded ByOdie Pastunik (DG Member) on 2-May-2006 Most Helpful Reviews Teruzzi Tested on Windows 7 x64 27 Nov 2013(5 minutes after download) Installation: Stability: Compatibility: "Driver not work